Search:

Why the feck can't people who post things for sale in the trading section read the Terms and Conditions....it's not rocket science and we all know you CAN read so please stick to the rules!...

http://www.maxbashing.com/mbforum/showthread.php?2476-Do-not-edit-your-opening-post-after-it-s-sold

http://www.maxbashing.com/mbforum/showthread.php?2476-Do-not-edit-your-opening-post-after-it-s-sold

Click the link below and you'll get video footage of the C B and A finals from this years TMSC 1st round which was held at LMCC....

I've never bothered drilling a hole on the opposite side, I've only ever just yanked the pin out and put it back together, done a couple trackside.

I'm seriously considering going back to my NiMhs, I have noticed that my servos don't seem to be as quick with LiPo and a reg, might be psychological but I'm not so sure

I use the Fiorini slider clutch and the Werks Power clutch...no problems with them in either my truggy or buggy and the shoes last for ages.
If you use the Fiorini clutch then change their 'made out...

Is it being fitted to an RTR model, the engine mounts on a lot RTR cars set the engine higher in the chassis to compensate for the spin starter/recoil starter attachment at the rear of the engine,...

Yeh but they are fun until they break woot

Nice job there bud, they look the dogs danglies. :applouse:

Adam drake, I believe, runs that way.

I foil the entire inside of my shells and have had no issues at all.... other than the fat twat holding the controller woot

I warm the tube where it comes out of the receiver box with a lighter, not with the wire in it, and bend it so that it runs inside the shell...has worked fine for the last 2 years

I'll be down, not sure what time as it depends on when I finish work.

Only 8 booked in as far as I can tell so looks to me like it's going to be pulled....shame really as I was looking forward to racing next week end. :apologetic:

Don't forget to get booked in folks, you only have until 12:00pm tomorrow, Saturday, or you'll get charged £12 on the day.

Booking in for this event closes at 12.00pm on Saturday so get on and book in for a great TMSC shake down opportunity.
Linky:-LMCC booking in form

Yup, the tyres that come with Losi truggies are XXT's, they are a good all round dirt tyre but are pants on astro.
1256 on steering and 1258 on whoa go duties are fine...the added bonus if you...

This Sunday LMCC are holding our 2012/2013 winter finals.
For those of you who have entered enough rounds during the winter season you will be in the main final, for those who have not there will...

Guest final is open to all, even if you haven't competed in any other of our winter rounds you're more than welcome to come up and enter.
You're more than welcome to come up with your leccy buggy...

I think Lee Dix wants to change from Buggy to Truggy...I'll give him a shout and try and get him converted lol

Jon Miller has a great tutorial on his site..
Linky:- http://www.rcsgraphicworx.co.uk/tutorials.php

Very clever bit of work here.
Watch this clip first:-
https://www.youtube.com/watch?v=X6jprOZ29wY&feature=youtube_gdata_player

Then this one:-...

Then I would check the gasket face of the case to check for moulding burrs and the inside also for burrs and check the gasket is seated properly....other than that you may well find that your case is...

It is down to one of 3 things...1-distorted internal diff case due to over-tightening or just general use , 2-crown gear screws being tightened up in wrong order or 3-a tiny amount of gasket still...